Before Unlocking The Wiko Power U10 Frp Lock Remove, Make Sure The Following Steps Are Performed:

Install MTK Driver Lasted

LINK – DOWNLOAD

Install libusb-win32-devel-filter Driver Lasted

LINK – DOWNLOAD

Login Username & Password On CM2-MT2

Select Local Auth On CM2 MT2

Operation : Reset Settings/Format FS [ v2.33 ]

Mode : FRP [ RESET PROTECTION ]

  1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
  2. Insert USB cable in phone
    Waiting for device connection …

PTFN : MediaTek USB Port_V1633 (COM3)
MODE : BOOTROM
PORT : 3
Waiting BOOT ack …
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Cervino
TYPE : MODERN [RAPHAEL]
BROM : MEID : DE252F96393E59C06740646A44B9D7BA
BROM : SecLevel : 0x000000E1
BROM : SecMode : SBC+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
BROM : SOCID : 9FAD119BA48838F260013E21C2E1717D08CC83B61E4EBD58397A6FC64455E307
BROM : EMI : Search
BROM : EMI : Found!
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA …
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA …
BROM : DA sent
BROM :Transfer control to DA …
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!

    EMMC: CID : D6010335384B3733316808EAB3247735
    EMMC: VEN : UNKNOWN [0xD6] : OEM : 3 : ID : 35384B373331 : PRV : 0x68
    EMMC: VEN : UNKNOWN [0xD6] : 58K731
    EMMC: SNN : 149599012 ( 0x08EAB324 ) , MF : 7/2020

 EMI : DEV : FireFly
 EMI : SRC : preloader_v745an.bin
 EMI : CNT : 0004
 EMI : Init EMI from INTERNAL DB
 EMI : EXT_RAM CFG Passed!

DA : BOOT to 2nd DA …
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

    SRAM: 0x0003A000 [ 232.00 KB ]
    DRAM: 0x80000000 [ 2.00 GB ]

    EMMC: CID : D6010335384B3733316808EAB3247735
    EMMC: VEN : UNKNOWN [0xD6] : OEM : 3 : ID : 35384B373331 : PRV : 0x68
    EMMC: VEN : UNKNOWN [0xD6] : 58K731
    EMMC: SNN : 149599012 ( 0x08EAB324 ) , MF : 7/2020

    EMMC: 
          BOOT1  : 0x00400000 [ 4.00 MB ]
          BOOT2  : 0x00400000 [ 4.00 MB ]
          RPMB   : 0x00400000 [ 4.00 MB ]
          USER   : 0x73A000000 [ 28.91 GB ]

    CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

    RNID : 6CDEE645CA44BB035DA1378A611AB6F4

DA : USB : HIGH-SPEED

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:36

Reconnect Power/Cable!

Download CM2-MT2 Lasted Version

LINK – DOWNLOAD

Download Wiko U10 Firmware

LINK – DOWNLOAD

By admin

Leave a Reply

Your email address will not be published.