Before Update.App Flash G620s-UL00, Make Sure The Following Steps Are Performed:

Install QcomMtk_Driver_Setup Lasted

LINK – DOWNLOAD

Download G620S-UL00 Full Firmware (C636)

LINK – DOWNLOAD

G620s-UL00 is a Qualcomm unit.Therefore, it is necessary to cover the back and support 9008 Test

First Extra Update.APP With UMT Dongle

Operation : Convert APP to QcFire Format
Extracting RPM…Done
Extracting TZ…Done
Extracting SBL1…Done
Extracting MODEM…Done
Extracting HYP…Done
Extracting MODEMST1…Done
Extracting MODEMST2…Done
Extracting FSG…Done
Extracting ABOOT…Done
Extracting RECOVERY…Done
Extracting SYSTEM…Done
Extracting USERDATA…Done
Extracting CACHE…Done
Extracting CUST…Done
Extracting PERSIST…Done
Extracting BOOT…Done
Saving Partition Table…Done
Saved to : C:\Users\koyen\OneDrive\Desktop\G620S-UL00_V100R001C636B264CUSTC636D003_Firmware_Myanmar_Nonspecific_Android 4.4.4_EMUI 2.3_05012YUS\Software\dload\Extracted\
Operation Finished.
QcFire Ver. 7.3

After Extra Firmware > Full Flash By 9008 With UMT Dongle

Operation : Flash
Checking for existing devices…Found
Port : HS-USB Diagnostics 9008 (COM91)
Driver Info : Mobile, qcusbser.sys, 2.1.2.2
Opening Port…OK
Init Handshake Sequence…OK
Hardware ID : E1507000 [8916] 00000000
OPK_DATA : 9CBA94693C2333A562BCF0E0E981C558748817D002F543B2A26AB1B4B3F1CF9E
Initializing Protocol…OK
Using Auto Loader Selection [1]
Preparing Loader…Done
Sending Loader [8916_014]…Done
Executing Loader…OK
Detecting Chip Type…OK
Hardware : 8916, EMMC, 8 GB
LU Count : 1 [0x00E90000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 16384, Sector Size: 512
Writing [RPM.img] -> [RPM] …Done
Writing [TZ.img] -> [TZ] …Done
Writing [SBL1.img] -> [SBL1] …Done
Writing [MODEM.img] -> [MODEM] …Done
Writing [HYP.img] -> [HYP] …Done
Writing [MODEMST1.img] -> [MODEMST1] …Done
Writing [MODEMST2.img] -> [MODEMST2] …Done
Writing [FSG.img] -> [FSG] …Done
Writing [ABOOT.img] -> [ABOOT] …Done
Writing [RECOVERY.img] -> [RECOVERY] …Done
Writing [SYSTEM.img ] -> [SYSTEM]…Done
Writing [USERDATA.img ] -> [USERDATA]…Done
Writing [CACHE.img ] -> [CACHE]…Done
Writing [CUST.img ] -> [CUST]…Done
Writing [PERSIST.img ] -> [PERSIST]…Done
Writing [BOOT.img] -> [BOOT] …Done
Writing [gpt_main0.bin] -> [PrimaryGPT] …Done
Applying Patches…………….Done
Resetting device…Done
Operation Finished.
QcFire Ver. 7.3

Download UMT QcFire Tool Lasted

LINK – DOWNLOAD

By admin

Leave a Reply

Your email address will not be published.