Vivo Y17 PD1901F Userlock Remove With Pandora Box

0/5 No votes

Report this app

Description

Before Unlocking The Vivo Y17 PD1901F Userlock, Make Sure The Following Steps Are Performed:

Install MTK Driver Lasted

LINK – DOWNLOAD

Install libusb-win32-devel-filter Driver Lasted

LINK – DOWNLOAD

  • Power Off Phone
  • Click Wipe Data On Pandora Box
  • Vol + Vol – / Connect Usb Cable
  • Selected model: Vivo PD1901F (Y17)
    Operation: Wipe Data
    Software version: 2.5

    There is a risk of data loss.
    This procedure will erase all User Data
    Make sure that you have a backup created. Continue? YES
    Host Power Off… OK
    Switch virtual port to USB… OK
    Connect Type-C to BOX… OK
    Host Power On… OK
    Wait for device… OK
    Read usbhost speed… HIGH
    Read Device Descriptor…
    Get VID/PID…0E8D/0003
    Send start cmd… OK
    Get HW code from device… 0766
    Get HW & SW version from device… OK
    HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
    Detect chip [MT6765]
    Get sec config… OK [000000E5]
    Active sec flags: [SBC DAA]
    Advanced Bypass Security… OK
    Disconnect virtual port… OK
    Connect Type-C to HUB… OK
    Wait for device connecting… OK
    Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
    Device found at COM34 [BROM]
    Open port… OK
    Send start cmd… OK
    Get HW code from device… 0766
    Get HW & SW version from device… OK
    HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
    Detect chip [MT6765]
    Library Version [2]
    Select platform… OK
    Init BROM… OK
    Force Charge… OK
    Disable WatchDog Timer… OK
    Reopen port for libver2… OK
    Get ME ID… OK
    ME_ID = 0xA9A609C0, 0x0B16FB42, 0x0D0F375F, 0x815F7C09
    Get Chip ID… [MT6765]
    Get SOC ID… [740785C6BE415A5040A92093795F9BC84235712E755FB6042BFA8F05ADF4D371]
    Get sec config… OK [000000E0]
    Load DownloadAgent… OK
    Search DA… OK [23]
    Send preloader… OK
    Start preloader… OK
    Check preloader answer… OK
    Send bootloader… OK
    Start bootloader… OK
    Wait for answer from bootloader… OK
    Send SYNC signal… OK
    Setup device enviroment… OK
    Setup device parametres… OK
    Receive DA SYNC signal… OK
    Set DA parametres… OK
    Get device connection agent… [BROM]
    Get device info… OK
    EMMC_ID: 0x150100525036344D42015F3FF2F9C635
    Load EMI from phone… OK
    Parse EMI config… OK
    Init EXT RAM… OK
    Send 2nd DA… OK
    Get device info… OK
    EMMC INFO:
    EMMC_ID : 0x150100525036344D42015F3FF2F9C635
    EMMC_BOOT1: 0x0000400000 (4.00Mb)
    EMMC_BOOT2: 0x0000400000 (4.00Mb)
    EMMC_RPMB : 0x0001000000 (16.00Mb)
    EMMC_USER : 0x0E8F800000 (58.24Gb)
    RAM INFO:
    INT_SRAM: 0x000003A000 (232.00Kb)
    EXT_RAM : 0x0100000000 (4.00Gb)
    Check USB status… USB_HIGH_SPEED
    Read partitions info from phone… OK
    Read partition “preloader”… OK
    Read partition “pgpt”… OK
    Read partition “nvcfg”… OK
    Read partition “nvdata”… OK
    Read partition “protect1″… OK
    Read partition “protect2″… OK
    Read partition “persist”… OK
    Read partition “proinfo”… OK
    Read partition “efuse”… OK
    Read partition “nvram”… OK
    Read partition “otp”… OK
    Read partition “flashinfo”… OK
    Format “userdata” partition… OK
    Wipe data done!

    Download Pandora Box Lasted Version

    LINK – DOWNLOAD

    Download Vivo Y17 Scatter Firmware

    LINK – DOWNLOAD

    Leave a Reply

    Your email address will not be published. Required fields are marked *