Report this app

Description

Before Global Change For Redmi 9A, Make Sure The Following Steps Are Performed:

Install MTK Driver Lasted

LINK – DOWNLOAD

Install libusb-win32-devel-filter Driver Lasted

LINK – DOWNLOAD
  • Power Off Phone
  • Click Write Firmware On Pandora Box
  • Vol + Vol – / Connect Usb Cable

Selected model: Xiaomi M2006C3LC (Redmi 9A)
Operation: Flash (Download only)
Software version: 2.5

Parse scatter file… OK
Load Rom Images… OK
Host Power Off… OK
Switch virtual port to USB… OK
Connect Type-C to BOX… OK
Host Power On… OK
Wait for device… OK
Read usbhost speed… HIGH
Read Device Descriptor…
Get VID/PID…0E8D/0003
Send start cmd… OK
Get HW code from device… 0766
Get HW & SW version from device… OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config… OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security… OK
Disconnect virtual port… OK
Connect Type-C to HUB… OK
Wait for device connecting… OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM34 [BROM]
Open port… OK
Send start cmd… OK
Get HW code from device… 0766
Get HW & SW version from device… OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform… OK
Init BROM… OK
Force Charge… OK
Disable WatchDog Timer… OK
Reopen port for libver2… OK
Get ME ID… OK
ME_ID = 0x51924EE1, 0x849B973B, 0xF0D369D1, 0x86244C81
Get Chip ID… [MT6765]
Get SOC ID… [7C00821179655A01EE916790820E0364B793608B777A786C81B08E6168FE58E5]
Get sec config… OK [000000E0]
Load DownloadAgent… OK
Search DA… OK [23]
Send preloader… OK
Start preloader… OK
Check preloader answer… OK
Send bootloader… OK
Start bootloader… OK
Wait for answer from bootloader… OK
Send SYNC signal… OK
Setup device enviroment… OK
Setup device parametres… OK
Receive DA SYNC signal… OK
Set DA parametres… OK
Get device connection agent… [BROM]
Get device info… OK
EMMC_ID: 0x150100434A54443452045C11BC848791
Load EMI config from preloader… OK
Init EXT RAM… OK
Send 2nd DA… OK
Get device info… OK
EMMC INFO:
EMMC_ID : 0x150100434A54443452045C11BC848791
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Get scatter info… OK
Check USB status… USB_HIGH_SPEED
Get scatter info… OK
Verify scatter file… OK
Do NAND BMT remark… OK
Setup download info… OK
Get partition table catagory… OK [GPT]
Read mirror partition table… OK
Check partition table layout changed… OK
Read major partition table… OK
Check major partition table layout changed… OK
Download “preloader”… OK
Download “recovery”… OK
Download “cust”… OK
Download “vbmeta_system”… OK
Download “vbmeta_vendor”… OK
Download “efuse”… OK
Download “md1img”… OK
Download “spmfw”… OK
Download “scp1″… OK
Download “scp2″… OK
Download “sspm_1″… OK
Download “sspm_2″… OK
Download “lk”… OK
Download “lk2″… OK
Download “boot”… OK
Download “logo”… OK
Download “dtbo”… OK
Download “tee1″… OK
Download “tee2″… OK
Download “super”… OK
Download “vbmeta”… OK
Download “cache”… OK
Download “userdata”… OK
Flashing done!

Download Pandora Box Lasted Version

LINK – DOWNLOAD

Redmi 9A Bootloader Unlock Pandora Box

LINK – VIEW

Download Redmi 9A Global ROM

LINK – DOWNLOAD

Download Redmi 9A ENG ROM

LINK – DOWNLOAD

Download Redmi 9A NVDATA Full Backup

LINK – DOWNLOAD

Leave a Reply

Your email address will not be published. Required fields are marked *